#include "stm32f4xx.h"
#include "stm32f4xx_rcc.h"
#include "stm32f4xx_gpio.h"
#include "stm32f4xx_can.h"
#include "misc.h"
#include "system_stm32f4xx.h"

#define USE_CAN1
/* #define USE_CAN2 */

#ifdef USE_CAN1
#define CANx CAN1
#else /* USE_CAN1 */
#define CANx CAN1
#endif /* USE_CAN1*/

void NVIC_Config();
void Rxmsg ();

void main()
{
SystemInit();
CAN_InitTypeDef CAN_InitStructure;
CAN_FilterInitTypeDef CAN_FilterInitStructure;
GPIO_InitTypeDef GPIO_InitStructure;

// Enable GPIO clock
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOD, ENABLE);
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOB, ENABLE);
// Configure CAN1 as alternate function
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_1;
GPIO_Init(GPIOD, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0;
GPIO_Init(GPIOD, &GPIO_InitStructure);



GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_OUT;
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_2MHz;
GPIO_Init(GPIOB, &GPIO_InitStructure);

// Connect PXx to CAN 1 2

GPIO_PinAFConfig(GPIOD, GPIO_PinSource0, GPIO_AF_CAN1); //CAN_RX = PD0
GPIO_PinAFConfig(GPIOD, GPIO_PinSource1, GPIO_AF_CAN1); //CAN_TX = PD1


// init CAN1
RCC_APB1PeriphClockCmd (RCC_APB1Periph_CAN1, ENABLE);

CAN_InitStructure.CAN_TTCM = DISABLE;
CAN_InitStructure.CAN_ABOM = DISABLE;
CAN_InitStructure.CAN_AWUM = DISABLE;
CAN_InitStructure.CAN_NART = DISABLE;
CAN_InitStructure.CAN_RFLM = DISABLE;
CAN_InitStructure.CAN_TXFP = DISABLE;

CAN_InitStructure.CAN_Prescaler = 16;// 125kbs
CAN_InitStructure.CAN_Mode = CAN_Mode_Normal;//LoopBack
CAN_InitStructure.CAN_SJW = CAN_SJW_1tq;
CAN_InitStructure.CAN_BS1 = CAN_BS1_14tq;
CAN_InitStructure.CAN_BS2 = CAN_BS2_6tq;

CAN_DeInit(CAN1);
CAN_Init(CAN1, &CAN_InitStructure);

// IT Configuration for CAN1 FIFO 0 message received interrupt
CAN_ITConfig(CAN1, CAN_IT_FMP0, ENABLE);
// IT Configuration for CAN1 FIFO 1 message received interrupt
CAN_ITConfig(CAN1, CAN_IT_FMP1, ENABLE);

/* CAN filter init */
#ifdef USE_CAN1
CAN_FilterInitStructure.CAN_FilterNumber = 0;
#else /* USE_CAN1 */
CAN_FilterInitStructure.CAN_FilterNumber = 0;
#endif /* USE_CAN1 */
CAN_FilterInitStructure.CAN_FilterMode = CAN_FilterMode_IdMask;
CAN_FilterInitStructure.CAN_FilterScale = CAN_FilterScale_32bit;
CAN_FilterInitStructure.CAN_FilterIdHigh = 0xFFFF;
CAN_FilterInitStructure.CAN_FilterIdLow = 0x0000;
CAN_FilterInitStructure.CAN_FilterMaskIdHigh = 0xFFFF;
CAN_FilterInitStructure.CAN_FilterMaskIdLow = 0x0000;
CAN_FilterInitStructure.CAN_FilterFIFOAssignment =CAN_FIFO0;

CAN_FilterInitStructure.CAN_FilterActivation = ENABLE;
CAN_FilterInit(&CAN_FilterInitStructure);

uint8_t TransmitMailbox = 0;
CanTxMsg TxMessage;
CanRxMsg RxMessage;
uint32_t i = 0;


void NVIC_Config()
{
NVIC_InitTypeDef NVIC_InitStructure;

/* Enable CANx RX0 interrupt IRQ channel */
#ifdef USE_CAN1
NVIC_InitStructure.NVIC_IRQChannel = CAN1_RX0_IRQn;
#else /* USE_CAN1 */
NVIC_InitStructure.NVIC_IRQChannel = CAN1_RX0_IRQn;
#endif /* USE_CAN1 */

NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
}



void Rxmsg()
{
RxMessage.StdId = 0x00;
RxMessage.ExtId = 0x00;
RxMessage.IDE = CAN_ID_STD;
RxMessage.DLC = 0;
RxMessage.FMI = 0;
for (i = 0; i < 8; i++)
{
RxMessage.Data[i] = 0;
}
CAN_Receive(CAN1, CAN_FIFO0, &RxMessage);

}


while(1){
CSsendmsg (),Rxmsg();
if (RxMessage.Data[0]== 0x01) GPIOB->BSRRL = GPIO_Pin_9;
int time = 3000000;
while(time>1){time--;}
time = 3000000;
while(time>1){time--;}
GPIOB->BSRRH = GPIO_Pin_9;



}}