case USART6_BASE:

#ifdef USE_IN_UART6_BUFFER
UART6_InputBufWR = 0;
UART6_InputBufRD = 0;
#endif

#ifdef USE_OUT_UART6_BUFFER
UART6_OutputBufWR = 0;
UART6_OutputBufRD = 0;
#endif

RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOC, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART6, ENABLE);

GPIO_PinAFConfig(GPIOC, GPIO_PinSource6, GPIO_AF_USART6);
GPIO_PinAFConfig(GPIOC, GPIO_PinSource7, GPIO_AF_USART6);

GPIO_Init_Struct.GPIO_Pin = GPIO_Pin_6;
GPIO_Init_Struct.GPIO_Mode = GPIO_Mode_AF;
GPIO_Init_Struct.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init_Struct.GPIO_OType = GPIO_OType_PP;
GPIO_Init_Struct.GPIO_PuPd = GPIO_PuPd_NOPULL;
GPIO_Init(GPIOC, &GPIO_Init_Struct);

GPIO_Init_Struct.GPIO_Pin = GPIO_Pin_7;
GPIO_Init_Struct.GPIO_OType = GPIO_OType_OD;
GPIO_Init_Struct.GPIO_PuPd = GPIO_PuPd_NOPULL;
GPIO_Init(GPIOC, &GPIO_Init_Struct);

#if defined (USE_IN_UART6_BUFFER) || defined (USE_OUT_UART6_BUFFER)
NVIC_InitStructure.NVIC_IRQChannel = USART6_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = UART6_PreemptionPriority;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = UART6_SubPriority;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
#endif
#ifdef USE_IN_UART6_BUFFER
USART_ITConfig(USARTx, USART_IT_RXNE, ENABLE);
//USART_ITConfig(USARTx, USART_IT_ORE, ENABLE);
#endif

break;
}

USART_Init_Struct.USART_BaudRate = Baudrate;
USART_Init_Struct.USART_WordLength = USART_WordLength_8b;
USART_Init_Struct.USART_StopBits = USART_StopBits_1;
USART_Init_Struct.USART_Parity = USART_Parity_No;
USART_Init_Struct.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
USART_Init_Struct.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_Init(USARTx, &USART_Init_Struct);

USART_Cmd(USARTx,ENABLE);

void USART6_IRQHandler(void)
{
if(USART_GetITStatus(USART6, USART_IT_TXE) != RESET)
{
#ifdef USE_OUT_UART6_BUFFER

if(UART6_out_counter != 0)
{
UART6_out_counter--;
USART_SendData(USART6,(uint16_t) UART6_OutputBuf[UART6_OutputBufRD]);

if(UART6_OutputBufRD >= (UART6_OutputBuf_size - 1))
{
UART6_OutputBufRD = 0;
}
else
{
UART6_OutputBufRD++;
}
} else {
USART_ITConfig(USART6, USART_IT_TXE, DISABLE);
isTxDone6 = 1;
#endif
}
} else if(USART_GetITStatus(USART6, USART_IT_RXNE) != RESET)
{
USART6->SR;
#ifdef USE_IN_UART6_BUFFER

uint8_t read_UART;

read_UART = USART_ReceiveData(USART6);
#ifdef FATFS_ON
GPSLOGGER_PushByte( read_UART );
#endif



if(UART6_in_counter < UART6_InputBuf_size)
{
UART6_InputBuf[UART6_InputBufWR] = read_UART;

if(UART6_InputBufWR == (UART6_InputBuf_size - 1))
{
UART6_InputBufWR = 0;
}
else
{
UART6_InputBufWR++;
}
UART6_in_counter++;
}
#endif
}else {
USART6->SR;
USART6->DR;
}

USART_ClearFlag( USART6, USART_FLAG_CTS | USART_FLAG_LBD | USART_FLAG_RXNE | USART_IT_TC );
}

inline void GPSLOGGER_PushByte( uint8_t b ){
__disable_irq();
if( sizebuf[curBuf] < LOGBUFSIZE ){
logbuf[ curBuf ][ sizebuf[curBuf] ] = b;
}
sizebuf[ curBuf ] ++;
__enable_irq();
}

    uint16_t status = USARTx->SR;
    uint8_t data = USARTx->DR;
    
    // чистим ошибки
    if (status & (USART_SR_ORE | USART_SR_NE | USART_SR_FE | USART_SR_PE))
        USARTx->SR = 0;
    
    if (status & USART_SR_RXNE)
    {
        // обрабатываем приём.
    }

    if (status & USART_SR_TXE)
    {
        // обрабатываем передачу.
    }

/******************************************************************************/
//
// IRQ Handler
//
void bufio_IRQHandler(bufio_FIFO *FIFO)
{
bufio_DRIVER* h = FIFO->HD; // to shorten the script
if (h && h->RI)
{
while (h->RI()) {

// If no more place in the input buffer, no char read out
// from the data register follows, and RI flag stays ON.
// The interrupt will be disabled. As soon as it is reenabled
// in the ReadChar, the interrupt shoots again.

if (bufio_RXBufferReady() && !FIFO->RX.flag)

bufio_StoreChar(FIFO, h->Get());

else {

h->RIE(0); // disable RX interrupt w/o getting the char
break; // from the device; it should keep the RI flag on.
}
}
}
....

/******************************************************************************/
//
// USART IRQ Handler
//
/******************************************************************************/
void STDIO_IRQHandler(void)
{
bufio_IRQHandler(&FIFO);
}

/******************************************************************************/
//
// USART IRQ Handler
//
/******************************************************************************/
void STDIO_IRQHandler(void)
{
if (STDIO_DEVICE->SR & USART_SR_ORE)
__NOP();
bufio_IRQHandler(&FIFO);
}

void STDIO_IRQHandler(void)
{
    STDIO_DEVICE->SR; // dummy read (ИМХО нафиг не надо)
    bufio_IRQHandler(&FIFO);
}

static INLINE void uart_isr(uart_t* const uart)
{
    uint_fast16_t status = uart->sfr->SR;

    if (status & USART_SR_RXNE)      // if RX data_reg isn't empty (auto-clr by reading data_reg)
    {  
        uart_rx_isr(uart, status);
    }
    else if (status & USART_SR_TXE)  // if TX data_reg is empty (auto-clr by writing data_reg)
    {
        uart_tx_isr(uart);
    }
}

//-----------------------------------------------------------------------------
// void USART2_IRQHandler(void)
//-----------------------------------------------------------------------------
void USART2_IRQHandler(void)
{
BYTE x;

if(USART2->SR & (1 << USART_SR_RXNE))
{
// новый символ в приемнике
x = USART2->DR;

crx++;

GPIOB->BSRR = (1 << 0);

if(x != ('0' + (cnt & 7)))
{
WORKLED_bit ^= 1;
cerror++;
eflag = 1;
}

GPIOB->BSRR = (1 << 0) << 16;
}

if((USART2->SR) & (1 << USART_SR_ORE)) USART2->DR;

}

//-----------------------------------------------------------------------------
// void EXTI3_IRQHandler(void)
//-----------------------------------------------------------------------------
void EXTI3_IRQHandler(void)
{
volatile int d;
if(EXTI->PR & (1 << 3))
{
cexti++;

GPIOB->BSRR = (1 << 1);
for(d = 0; d < 1000; d++);

EXTI->PR = (1 << 3);
GPIOB->BSRR = (1 << 1) << 16;
}
}