module pll (
    areset,
    inclk0,
    c0,
    c1,
    c2,
    c3,
    locked);

    input      areset;
    input      inclk0;
    output      c0;
    output      c1;
    output      c2;
    output      c3;
    output      locked;
`ifndef ALTERA_RESERVED_QIS
// synopsys translate_off
`endif
    tri0      areset;
`ifndef ALTERA_RESERVED_QIS
// synopsys translate_on
`endif

    wire [4:0] sub_wire0;
    wire  sub_wire3;
    wire [0:0] sub_wire8 = 1'h0;
    wire [2:2] sub_wire5 = sub_wire0[2:2];
    wire [0:0] sub_wire4 = sub_wire0[0:0];
    wire [3:3] sub_wire2 = sub_wire0[3:3];
    wire [1:1] sub_wire1 = sub_wire0[1:1];
    wire  c1 = sub_wire1;
    wire  c3 = sub_wire2;
    wire  locked = sub_wire3;
    wire  c0 = sub_wire4;
    wire  c2 = sub_wire5;
    wire  sub_wire6 = inclk0;
    wire [1:0] sub_wire7 = {sub_wire8, sub_wire6};

    altpll    altpll_component (
                .areset (areset),
                .inclk (sub_wire7),
                .clk (sub_wire0),
                .locked (sub_wire3),
                .activeclock (),
                .clkbad (),
                .clkena ({6{1'b1}}),
                .clkloss (),
                .clkswitch (1'b0),
                .configupdate (1'b0),
                .enable0 (),
                .enable1 (),
                .extclk (),
                .extclkena ({4{1'b1}}),
                .fbin (1'b1),
                .fbmimicbidir (),
                .fbout (),
                .fref (),
                .icdrclk (),
                .pfdena (1'b1),
                .phasecounterselect ({4{1'b1}}),
                .phasedone (),
                .phasestep (1'b1),
                .phaseupdown (1'b1),
                .pllena (1'b1),
                .scanaclr (1'b0),
                .scanclk (1'b0),
                .scanclkena (1'b1),
                .scandata (1'b0),
                .scandataout (),
                .scandone (),
                .scanread (1'b0),
                .scanwrite (1'b0),
                .sclkout0 (),
                .sclkout1 (),
                .vcooverrange (),
                .vcounderrange ());
    defparam
        altpll_component.bandwidth_type = "LOW",
        altpll_component.clk0_divide_by = 5,
        altpll_component.clk0_duty_cycle = 50,
        altpll_component.clk0_multiply_by = 36,
        altpll_component.clk0_phase_shift = "0",
        altpll_component.clk1_divide_by = 5,
        altpll_component.clk1_duty_cycle = 50,
        altpll_component.clk1_multiply_by = 36,
        altpll_component.clk1_phase_shift = "347",
        altpll_component.clk2_divide_by = 5,
        altpll_component.clk2_duty_cycle = 50,
        altpll_component.clk2_multiply_by = 36,
        altpll_component.clk2_phase_shift = "694",
        altpll_component.clk3_divide_by = 5,
        altpll_component.clk3_duty_cycle = 50,
        altpll_component.clk3_multiply_by = 36,
        altpll_component.clk3_phase_shift = "1042",
        altpll_component.compensate_clock = "CLK3",
        altpll_component.inclk0_input_frequency = 20000,
        altpll_component.intended_device_family = "Cyclone III",
        altpll_component.lpm_hint = "CBX_MODULE_PREFIX=pll",
        altpll_component.lpm_type = "altpll",
        altpll_component.operation_mode = "NORMAL",
        altpll_component.pll_type = "AUTO",
        altpll_component.port_activeclock = "PORT_UNUSED",
        altpll_component.port_areset = "PORT_USED",
        altpll_component.port_clkbad0 = "PORT_UNUSED",
        altpll_component.port_clkbad1 = "PORT_UNUSED",
        altpll_component.port_clkloss = "PORT_UNUSED",
        altpll_component.port_clkswitch = "PORT_UNUSED",
        altpll_component.port_configupdate = "PORT_UNUSED",
        altpll_component.port_fbin = "PORT_UNUSED",
        altpll_component.port_inclk0 = "PORT_USED",
        altpll_component.port_inclk1 = "PORT_UNUSED",
        altpll_component.port_locked = "PORT_USED",
        altpll_component.port_pfdena = "PORT_UNUSED",
        altpll_component.port_phasecounterselect = "PORT_UNUSED",
        altpll_component.port_phasedone = "PORT_UNUSED",
        altpll_component.port_phasestep = "PORT_UNUSED",
        altpll_component.port_phaseupdown = "PORT_UNUSED",
        altpll_component.port_pllena = "PORT_UNUSED",
        altpll_component.port_scanaclr = "PORT_UNUSED",
        altpll_component.port_scanclk = "PORT_UNUSED",
        altpll_component.port_scanclkena = "PORT_UNUSED",
        altpll_component.port_scandata = "PORT_UNUSED",
        altpll_component.port_scandataout = "PORT_UNUSED",
        altpll_component.port_scandone = "PORT_UNUSED",
        altpll_component.port_scanread = "PORT_UNUSED",
        altpll_component.port_scanwrite = "PORT_UNUSED",
        altpll_component.port_clk0 = "PORT_USED",
        altpll_component.port_clk1 = "PORT_USED",
        altpll_component.port_clk2 = "PORT_USED",
        altpll_component.port_clk3 = "PORT_USED",
        altpll_component.port_clk4 = "PORT_UNUSED",
        altpll_component.port_clk5 = "PORT_UNUSED",
        altpll_component.port_clkena0 = "PORT_UNUSED",
        altpll_component.port_clkena1 = "PORT_UNUSED",
        altpll_component.port_clkena2 = "PORT_UNUSED",
        altpll_component.port_clkena3 = "PORT_UNUSED",
        altpll_component.port_clkena4 = "PORT_UNUSED",
        altpll_component.port_clkena5 = "PORT_UNUSED",
        altpll_component.port_extclk0 = "PORT_UNUSED",
        altpll_component.port_extclk1 = "PORT_UNUSED",
        altpll_component.port_extclk2 = "PORT_UNUSED",
        altpll_component.port_extclk3 = "PORT_UNUSED",
        altpll_component.self_reset_on_loss_lock = "OFF",
        altpll_component.width_clock = 5;


endmodule