/*****************************************************
Chip type : ATxmega128A3
Program type : Application
AVR Core Clock frequency: 4,608000 MHz
Memory model : Small
Data Stack size : 2048
*****************************************************/
// I/O Registers definitions
#include <io.h>
#define E 0
#define WR 1
#define A0 2
#define CS 3
#define RST 4
#define DSF 5
#define Button1 6
#define Button2 7
#define D0 0
#define D1 1
#define D2 2
#define D3 3
#define D4 4
#define D5 5
#define D6 6
#define D7 7
#define Data_PORT PORTD.OUT
#define Ctrl_PORT PORTE.OUT
#define Data_DIR PORTD.DIR
#define Ctrl_DIR PORTE.DIR
#define SystemSet 0x40
#define SleepIn 0x53
#define DispOff 0x58
#define DispOn 0x59
#define Scroll 0x44
#define CurForm 0x5D
#define CGRAMAddr 0x5C
#define CurRight 0x4C
#define CurLeft 0x4D
#define CurUp 0x4E
#define CurDown 0x4F
#define HdotScr 0x5A
#define Overlay 0x5B
#define SetCurAddr 0x46
#define ReadCurAddr 0x47
#define MemWrite 0x42
#define MemRead 0x43
void Delay(unsigned int);
void Ports_Init(void);
void system_clocks_init(void);
void SendLcdCommand(unsigned char);
void SendLcdData(unsigned char);
void Delay(unsigned int);
void ClearText(void);
void ClearGraphics(void);
void InstructionSet(void);
// Declare your global variables here
int i=1;
void main(void)
{
// Declare your local variables here
unsigned char n;
// Interrupt system initialization
// Optimize for speed
#pragma optsize-
// Make sure the interrupts are disabled
#asm("cli")
// Low level interrupt: Off
// Round-robin scheduling for low level interrupt: Off
// Medium level interrupt: Off
// High level interrupt: Off
// The interrupt vectors will be placed at the start of the Application FLASH section
n=(PMIC.CTRL & (~(PMIC_RREN_bm | PMIC_IVSEL_bm | PMIC_HILVLEN_bm | PMIC_MEDLVLEN_bm | PMIC_LOLVLEN_bm)));
CCP=CCP_IOREG_gc;
PMIC.CTRL=n;
// Set the default priority for round-robin scheduling
PMIC.INTPRI=0x00;
// Restore optimization for size if needed
#pragma optsize_default
system_clocks_init();
Ports_Init();
Delay(i);
InstructionSet();
Ctrl_PORT|=(1<<CS);
while (1)
{
// Place your code here
}
}
// System Clocks initialization
void system_clocks_init(void)
{
unsigned char n,s;
// Optimize for speed
#pragma optsize-
// Save interrupts enabled/disabled state
s=SREG;
// Disable interrupts
#asm("cli")
// External 4608,000 kHz clock source on XTAL1 initialization
OSC.XOSCCTRL=OSC_XOSCSEL_EXTCLK_gc;
// Enable the external clock source
OSC.CTRL|=OSC_XOSCEN_bm;
// System Clock prescaler A division factor: 1
// System Clock prescalers B & C division factors: B:1, C:1
// ClkPer4: 4608,000 kHz
// ClkPer2: 4608,000 kHz
// ClkPer: 4608,000 kHz
// ClkCPU: 4608,000 kHz
n=(CLK.PSCTRL & (~(CLK_PSADIV_gm | CLK_PSBCDIV1_bm | CLK_PSBCDIV0_bm))) |
CLK_PSADIV_1_gc | CLK_PSBCDIV_1_1_gc;
CCP=CCP_IOREG_gc;
CLK.PSCTRL=n;
// Select the system clock source: External Osc. or Clock
n=(CLK.CTRL & (~CLK_SCLKSEL_gm)) | CLK_SCLKSEL_XOSC_gc;
CCP=CCP_IOREG_gc;
CLK.CTRL=n;
// Disable the unused oscillators: 2 MHz, 32 MHz, internal 32 kHz, PLL
OSC.CTRL&= ~(OSC_RC2MEN_bm | OSC_RC32MEN_bm | OSC_RC32KEN_bm | OSC_PLLEN_bm);
// Peripheral Clock output: Disabled
PORTCFG.CLKEVOUT=(PORTCFG.CLKEVOUT & (~PORTCFG_CLKOUT_gm)) | PORTCFG_CLKOUT_OFF_gc;
// Restore interrupts enabled/disabled state
SREG=s;
// Restore optimization for size if needed
#pragma optsize_default
}
// Ports initialization
void Ports_Init(void)
{
// PORTA initialization
// OUT register
PORTA.OUT=0x00;
// Bit0: Input
// Bit1: Input
// Bit2: Input
// Bit3: Input
// Bit4: Input
// Bit5: Input
// Bit6: Input
// Bit7: Input
PORTA.DIR=0x00;
// Bit0 Output/Pull configuration: Totempole/No
// Bit0 Input/Sense configuration: Sense both edges
// Bit0 inverted: Off
// Bit0 slew rate limitation: Off
PORTA.PIN0CTRL=PORT_OPC_TOTEM_gc | PORT_ISC_BOTHEDGES_gc;
// Bit1 Output/Pull configuration: Totempole/No
// Bit1 Input/Sense configuration: Sense both edges
// Bit1 inverted: Off
// Bit1 slew rate limitation: Off
PORTA.PIN1CTRL=PORT_OPC_TOTEM_gc | PORT_ISC_BOTHEDGES_gc;
// Bit2 Output/Pull configuration: Totempole/No
// Bit2 Input/Sense configuration: Sense both edges
// Bit2 inverted: Off
// Bit2 slew rate limitation: Off
PORTA.PIN2CTRL=PORT_OPC_TOTEM_gc | PORT_ISC_BOTHEDGES_gc;
// Bit3 Output/Pull configuration: Totempole/No
// Bit3 Input/Sense configuration: Sense both edges
// Bit3 inverted: Off
// Bit3 slew rate limitation: Off
PORTA.PIN3CTRL=PORT_OPC_TOTEM_gc | PORT_ISC_BOTHEDGES_gc;
// Bit4 Output/Pull configuration: Totempole/No
// Bit4 Input/Sense configuration: Sense both edges
// Bit4 inverted: Off
// Bit4 slew rate limitation: Off
PORTA.PIN4CTRL=PORT_OPC_TOTEM_gc | PORT_ISC_BOTHEDGES_gc;
// Bit5 Output/Pull configuration: Totempole/No
// Bit5 Input/Sense configuration: Sense both edges
// Bit5 inverted: Off
// Bit5 slew rate limitation: Off
PORTA.PIN5CTRL=PORT_OPC_TOTEM_gc | PORT_ISC_BOTHEDGES_gc;
// Bit6 Output/Pull configuration: Totempole/No
// Bit6 Input/Sense configuration: Sense both edges
// Bit6 inverted: Off
// Bit6 slew rate limitation: Off
PORTA.PIN6CTRL=PORT_OPC_TOTEM_gc | PORT_ISC_BOTHEDGES_gc;
// Bit7 Output/Pull configuration: Totempole/No
// Bit7 Input/Sense configuration: Sense both edges
// Bit7 inverted: Off
// Bit7 slew rate limitation: Off
PORTA.PIN7CTRL=PORT_OPC_TOTEM_gc | PORT_ISC_BOTHEDGES_gc;
// Interrupt 0 level: Disabled
// Interrupt 1 level: Disabled
PORTA.INTCTRL=(PORTA.INTCTRL & (~(PORT_INT1LVL_gm | PORT_INT0LVL_gm))) |
PORT_INT1LVL_OFF_gc | PORT_INT0LVL_OFF_gc;
// Bit0 pin change interrupt 0: Off
// Bit1 pin change interrupt 0: Off
// Bit2 pin change interrupt 0: Off
// Bit3 pin change interrupt 0: Off
// Bit4 pin change interrupt 0: Off
// Bit5 pin change interrupt 0: Off
// Bit6 pin change interrupt 0: Off
// Bit7 pin change interrupt 0: Off
PORTA.INT0MASK=0x00;
// Bit0 pin change interrupt 1: Off
// Bit1 pin change interrupt 1: Off
// Bit2 pin change interrupt 1: Off
// Bit3 pin change interrupt 1: Off
// Bit4 pin change interrupt 1: Off
// Bit5 pin change interrupt 1: Off
// Bit6 pin change interrupt 1: Off
// Bit7 pin change interrupt 1: Off
PORTA.INT1MASK=0x00;
// PORTD initialization
// OUT register
PORTD.OUT=0x00;
// Bit0: Output
// Bit1: Output
// Bit2: Output
// Bit3: Output
// Bit4: Output
// Bit5: Output
// Bit6: Output
// Bit7: Output
PORTD.DIR=0xFF;
// Bit0 Output/Pull configuration: Totempole/No
// Bit0 Input/Sense configuration: Sense both edges
// Bit0 inverted: Off
// Bit0 slew rate limitation: Off
PORTD.PIN0CTRL=PORT_OPC_TOTEM_gc | PORT_ISC_BOTHEDGES_gc;
// Bit1 Output/Pull configuration: Totempole/No
// Bit1 Input/Sense configuration: Sense both edges
// Bit1 inverted: Off
// Bit1 slew rate limitation: Off
PORTD.PIN1CTRL=PORT_OPC_TOTEM_gc | PORT_ISC_BOTHEDGES_gc;
// Bit2 Output/Pull configuration: Totempole/No
// Bit2 Input/Sense configuration: Sense both edges
// Bit2 inverted: Off
// Bit2 slew rate limitation: Off
PORTD.PIN2CTRL=PORT_OPC_TOTEM_gc | PORT_ISC_BOTHEDGES_gc;
// Bit3 Output/Pull configuration: Totempole/No
// Bit3 Input/Sense configuration: Sense both edges
// Bit3 inverted: Off
// Bit3 slew rate limitation: Off
PORTD.PIN3CTRL=PORT_OPC_TOTEM_gc | PORT_ISC_BOTHEDGES_gc;
// Bit4 Output/Pull configuration: Totempole/No
// Bit4 Input/Sense configuration: Sense both edges
// Bit4 inverted: Off
// Bit4 slew rate limitation: Off
PORTD.PIN4CTRL=PORT_OPC_TOTEM_gc | PORT_ISC_BOTHEDGES_gc;
// Bit5 Output/Pull configuration: Totempole/No
// Bit5 Input/Sense configuration: Sense both edges
// Bit5 inverted: Off
// Bit5 slew rate limitation: Off
PORTD.PIN5CTRL=PORT_OPC_TOTEM_gc | PORT_ISC_BOTHEDGES_gc;
// Bit6 Output/Pull configuration: Totempole/No
// Bit6 Input/Sense configuration: Sense both edges
// Bit6 inverted: Off
// Bit6 slew rate limitation: Off
PORTD.PIN6CTRL=PORT_OPC_TOTEM_gc | PORT_ISC_BOTHEDGES_gc;
// Bit7 Output/Pull configuration: Totempole/No
// Bit7 Input/Sense configuration: Sense both edges
// Bit7 inverted: Off
// Bit7 slew rate limitation: Off
PORTD.PIN7CTRL=PORT_OPC_TOTEM_gc | PORT_ISC_BOTHEDGES_gc;
// Interrupt 0 level: Disabled
// Interrupt 1 level: Disabled
PORTD.INTCTRL=(PORTD.INTCTRL & (~(PORT_INT1LVL_gm | PORT_INT0LVL_gm))) |
PORT_INT1LVL_OFF_gc | PORT_INT0LVL_OFF_gc;
// Bit0 pin change interrupt 0: Off
// Bit1 pin change interrupt 0: Off
// Bit2 pin change interrupt 0: Off
// Bit3 pin change interrupt 0: Off
// Bit4 pin change interrupt 0: Off
// Bit5 pin change interrupt 0: Off
// Bit6 pin change interrupt 0: Off
// Bit7 pin change interrupt 0: Off
PORTD.INT0MASK=0x00;
// Bit0 pin change interrupt 1: Off
// Bit1 pin change interrupt 1: Off
// Bit2 pin change interrupt 1: Off
// Bit3 pin change interrupt 1: Off
// Bit4 pin change interrupt 1: Off
// Bit5 pin change interrupt 1: Off
// Bit6 pin change interrupt 1: Off
// Bit7 pin change interrupt 1: Off
PORTD.INT1MASK=0x00;
// PORTE initialization
// OUT register
PORTE.OUT=0x00;
// Bit0: Output
// Bit1: Input
// Bit2: Output
// Bit3: Output
// Bit4: Output
// Bit5: Output
// Bit6: Output
// Bit7: Output
PORTE.DIR=0xFD;
// Bit0 Output/Pull configuration: Totempole/No
// Bit0 Input/Sense configuration: Sense both edges
// Bit0 inverted: Off
// Bit0 slew rate limitation: Off
PORTE.PIN0CTRL=PORT_OPC_TOTEM_gc | PORT_ISC_BOTHEDGES_gc;
// Bit1 Output/Pull configuration: Totempole/No
// Bit1 Input/Sense configuration: Sense both edges
// Bit1 inverted: Off
// Bit1 slew rate limitation: Off
PORTE.PIN1CTRL=PORT_OPC_TOTEM_gc | PORT_ISC_BOTHEDGES_gc;
// Bit2 Output/Pull configuration: Totempole/No
// Bit2 Input/Sense configuration: Sense both edges
// Bit2 inverted: Off
// Bit2 slew rate limitation: Off
PORTE.PIN2CTRL=PORT_OPC_TOTEM_gc | PORT_ISC_BOTHEDGES_gc;
// Bit3 Output/Pull configuration: Totempole/No
// Bit3 Input/Sense configuration: Sense both edges
// Bit3 inverted: Off
// Bit3 slew rate limitation: Off
PORTE.PIN3CTRL=PORT_OPC_TOTEM_gc | PORT_ISC_BOTHEDGES_gc;
// Bit4 Output/Pull configuration: Totempole/No
// Bit4 Input/Sense configuration: Sense both edges
// Bit4 inverted: Off
// Bit4 slew rate limitation: Off
PORTE.PIN4CTRL=PORT_OPC_TOTEM_gc | PORT_ISC_BOTHEDGES_gc;
// Bit5 Output/Pull configuration: Totempole/No
// Bit5 Input/Sense configuration: Sense both edges
// Bit5 inverted: Off
// Bit5 slew rate limitation: Off
PORTE.PIN5CTRL=PORT_OPC_TOTEM_gc | PORT_ISC_BOTHEDGES_gc;
// Bit6 Output/Pull configuration: Totempole/No
// Bit6 Input/Sense configuration: Sense both edges
// Bit6 inverted: Off
// Bit6 slew rate limitation: Off
PORTE.PIN6CTRL=PORT_OPC_TOTEM_gc | PORT_ISC_BOTHEDGES_gc;
// Bit7 Output/Pull configuration: Totempole/No
// Bit7 Input/Sense configuration: Sense both edges
// Bit7 inverted: Off
// Bit7 slew rate limitation: Off
PORTE.PIN7CTRL=PORT_OPC_TOTEM_gc | PORT_ISC_BOTHEDGES_gc;
// Interrupt 0 level: Disabled
// Interrupt 1 level: Disabled
PORTE.INTCTRL=(PORTE.INTCTRL & (~(PORT_INT1LVL_gm | PORT_INT0LVL_gm))) |
PORT_INT1LVL_OFF_gc | PORT_INT0LVL_OFF_gc;
// Bit0 pin change interrupt 0: Off
// Bit1 pin change interrupt 0: Off
// Bit2 pin change interrupt 0: Off
// Bit3 pin change interrupt 0: Off
// Bit4 pin change interrupt 0: Off
// Bit5 pin change interrupt 0: Off
// Bit6 pin change interrupt 0: Off
// Bit7 pin change interrupt 0: Off
PORTE.INT0MASK=0x00;
// Bit0 pin change interrupt 1: Off
// Bit1 pin change interrupt 1: Off
// Bit2 pin change interrupt 1: Off
// Bit3 pin change interrupt 1: Off
// Bit4 pin change interrupt 1: Off
// Bit5 pin change interrupt 1: Off
// Bit6 pin change interrupt 1: Off
// Bit7 pin change interrupt 1: Off
PORTE.INT1MASK=0x00;
// PORTR initialization
// OUT register
PORTR.OUT=0x00;
// Bit0: Input
// Bit1: Input
PORTR.DIR=0x00;
// Bit0 Output/Pull configuration: Totempole/No
// Bit0 Input/Sense configuration: Sense both edges
// Bit0 inverted: Off
// Bit0 slew rate limitation: Off
PORTR.PIN0CTRL=PORT_OPC_TOTEM_gc | PORT_ISC_BOTHEDGES_gc;
// Bit1 Output/Pull configuration: Totempole/No
// Bit1 Input/Sense configuration: Sense both edges
// Bit1 inverted: Off
// Bit1 slew rate limitation: Off
PORTR.PIN1CTRL=PORT_OPC_TOTEM_gc | PORT_ISC_BOTHEDGES_gc;
// Interrupt 0 level: Disabled
// Interrupt 1 level: Disabled
PORTR.INTCTRL=(PORTR.INTCTRL & (~(PORT_INT1LVL_gm | PORT_INT0LVL_gm))) |
PORT_INT1LVL_OFF_gc | PORT_INT0LVL_OFF_gc;
// Bit0 pin change interrupt 0: Off
// Bit1 pin change interrupt 0: Off
PORTR.INT0MASK=0x00;
// Bit0 pin change interrupt 1: Off
// Bit1 pin change interrupt 1: Off
PORTR.INT1MASK=0x00;
}
void SendLcdCommand(unsigned char Command)
{
Ctrl_PORT |= 1<<A0;
Data_PORT = Command;
Ctrl_PORT |= (0<<WR);
Ctrl_PORT |= (1<<E);
Delay(i);
Ctrl_PORT |= (1<<WR)|(0<<E);
}
void SendLcdData(unsigned char Data)
{
Ctrl_PORT |= (0<<A0);
Data_PORT = Data;
Ctrl_PORT |= (0<<WR);
Ctrl_PORT |= (1<<E);
Delay(i);
Ctrl_PORT = (1<<WR)|(0<<E);
}
void Delay(unsigned int counter)
{
while(counter)
{
counter = counter - 1;
}
}
void ClearText(void)
{
SendLcdCommand(SetCurAddr);
SendLcdData(0x00);
SendLcdData(0x00);
SendLcdCommand(CurRight);
SendLcdCommand(MemWrite);
for(i = 0; i <= 1200; i++)
{
SendLcdData(0x20);
}
}
void ClearGraphics(void)
{
SendLcdCommand(SetCurAddr);
SendLcdData(0x00);
SendLcdData(0x10);
SendLcdCommand(CurRight);
SendLcdCommand(MemWrite);
for(i = 0; i <= 9600; i++)
{
SendLcdData(0x00);
}
}
void InstructionSet(void)
{
SendLcdCommand(SystemSet); //System
SendLcdData(0x38);
SendLcdData(0x87);
SendLcdData(0x07);
SendLcdData(0x3F);
SendLcdData(0x49);//(0x2B)
SendLcdData(0x7F);//(EF)
SendLcdData(0x80);//(0x28)
SendLcdData(0x00);
SendLcdCommand(Scroll); //Scroll
SendLcdData(0x00);
SendLcdData(0x00);
SendLcdData(0x40);//(0xEF)
SendLcdData(0x00);
SendLcdData(0x10);
SendLcdData(0x40);//(0xEF)
SendLcdData(0x00);
SendLcdData(0x04);
SendLcdData(0x00);
SendLcdData(0x30);
SendLcdCommand(HdotScr); // HDOTSCR
SendLcdData(0x00);
SendLcdCommand(Overlay); //OVLAY
SendLcdData(0x01);
SendLcdCommand(DispOff); //DISPOFF
SendLcdData(0x56); //(0x00)
ClearText();
ClearGraphics();
SendLcdCommand(SetCurAddr); //CSRW
SendLcdData(0x00);
SendLcdData(0x00);
SendLcdCommand(CurForm); //CSR FORM
SendLcdData(0x00);
SendLcdData(0x00);
SendLcdCommand(DispOn); //DISP ON
SendLcdData(0x14);
Ctrl_PORT|=(1<<DSF);
SendLcdCommand(CurRight); //CSR DIR
SendLcdCommand(MemWrite); //MWRITE
SendLcdData(0x20);
SendLcdData(0x45);
SendLcdData(0x50);
SendLcdData(0x53);
SendLcdData(0x4F);
SendLcdData(0x4E);
SendLcdCommand(SetCurAddr); //CSRW
SendLcdData(0x00);
SendLcdData(0x10);
SendLcdCommand(CurDown); //CSRDIR 0x4F
SendLcdCommand(MemWrite); //MWRITE
SendLcdData(0xFF);
SendLcdData(0xFF);
SendLcdData(0xFF);
SendLcdData(0xFF);
SendLcdData(0xFF);
SendLcdData(0xFF);
SendLcdData(0xFF);
SendLcdData(0xFF);
SendLcdData(0xFF);
SendLcdCommand(SetCurAddr); //CSRW
SendLcdData(0x01);
SendLcdData(0x10);
SendLcdCommand(MemWrite); //MWRITE
SendLcdData(0xFF);
SendLcdData(0xFF);
SendLcdData(0xFF);
SendLcdData(0xFF);
SendLcdData(0xFF);
SendLcdData(0xFF);
SendLcdData(0xFF);
SendLcdData(0xFF);
SendLcdData(0xFF);
SendLcdCommand(SetCurAddr); //CSRW
SendLcdData(0x00);
SendLcdData(0x01);
SendLcdCommand(CurRight); //CSRDIR
SendLcdCommand(MemWrite); //MWRITE
SendLcdData(0x44);
SendLcdData(0x6F);
SendLcdData(0x74);
SendLcdData(0x20);
SendLcdData(0x4D);
SendLcdData(0x61);
SendLcdData(0x74);
SendLcdData(0x72);
SendLcdData(0x69);
SendLcdData(0x78);
SendLcdData(0x20);
SendLcdData(0x4C);
SendLcdData(0x43);
SendLcdData(0x44);
SendLcdCommand(SetCurAddr);
SendLcdData(0x00);
SendLcdData(0x00);
SendLcdCommand(CurForm);
SendLcdData(0x04);
SendLcdData(0x86);
}
Так вторая нога же Vdd. Может относительно первой ноги? Диапазон (-22.8~-12.4)В.
Появляются прямые линии. Мусор?
Bolymin BG320240B
Dec 19 2010, 14:20
)
