кто нибудь использовал U-Boot 1.3.2 ? Опции

[Badwin]

Попробывал скомпилить U-Boot 1.3.2 под свою плату, запускается, при выполнеение команды "boot" вылетает с таким сообщением

Load U-BOOT from dataflash[c0008000] to SDRAM[20f00000]

Set PLLA to 180Mhz and Master clock to 45Mhz and start U-BOOTя

U-Boot 1.3.2 (Mar 13 2008 - 04:24:42)

DRAM: 32 MB
Atmel: Flash: 0 kB
DataFlash:AT45DB642
Nb pages: 8192
Page Size: 1056
Size= 8650752 bytes
Logical address: 0xC0000000
Area 0: C0000000 to C0007FFF (RO)
Area 1: C0008000 to C001FFFF (RO)
Area 2: C0020000 to C0027FFF
Area 3: C0028000 to C083FFFF
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 3  0
U-Boot> printenv
bootdelay=3
baudrate=115200
ethaddr=12:34:56:78:9A:BC
ipaddr=10.0.0.2
serverip=10.0.0.1
netmask=255.0.0.0
bootfile="u-boot.bin.gz"
bootcmd=cp.b 0xC002A000 0x20A00000 0x200000; bootm 0x20A00000
stdin=serial
stdout=serial
stderr=serial

Environment size: 234/8188 bytes
U-Boot> boot
Copy to Flash... data abort
pc : [<20f11c84>] lr : [<20f0c280>]
sp : 20edd7c8 ip : 20f1aba4 fp : c002a000
r10: 20f1c32c r9 : 20f1c32c r8 : 20eddfdc
r7 : 20f1c32c r6 : c002a000 r5 : 20a00000 r4 : 00200000
r3 : 00200000 r2 : 20a00000 r1 : c002a000 r0 : 20f1c32c
Flags: nzCv IRQs off FIQs off Mode SVC_32
Resetting CPU ...

может кто подскажет в чем проблема?

[Badwin]

в общем победил


AT91F_LowLevelInit(): Debug channel initialized
press any key to enter bootloader
Load U-BOOT from dataflash[c0008000] to SDRAM[20f00000]
Set PLLA to 180Mhz and Master clock to 45Mhz and start U-BOOTя

U-Boot 1.3.2 (Mar 20 2008 - 05:38:57)

DRAM: 32 MB
Atmel: Flash: 0 kB
DataFlash:AT45DB642
Nb pages: 8192
Page Size: 1056
Size= 8650752 bytes
Logical address: 0xC0000000
Area 0: C0000000 to C0007FFF (RO)
Area 1: C0008000 to C001FFFF (RO)
Area 2: C0020000 to C0027FFF
Area 3: C0028000 to C083FFFF
In: serial
Out: serial
Err: serial
eth: setteng MAC address to 12:34:56:78:9a:bc
RTL8201PHY not connected!!

Link: 100baseTX Full Duplex
Hit any key to stop autoboot: 3  2  1  0
## Booting image at c002a000 ...
Image Name:
Image Type: ARM Linux Kernel Image (gzip compressed)
Data Size: 1257717 Bytes = 1.2 MB
Load Address: 20008000
Entry Point: 20008000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK

Starting kernel ...

Linux version 2.6.23 (root@box) (gcc version 3.4.6) #72 PREEMPT Tue Mar 11 22:41:45 EDT 2008
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0003177
Machine: MY AT91RM9200
Memory policy: ECC disabled, Data cache writeback
Clocks: CPU 179 MHz, master 44 MHz, main 18.432 MHz
и т.д


немного отличается командами,
setenv bootcmd=bootm 0xC002A000
boot
с сетью пока не разбирался...
в общем можно u-boot-1.3.2. запускать AT91RM9200 если немного подшаманить.......