mc3phac, не получается запустить :( Опции

[raider]

Никто не работал с мс mc3phac? Это контроллер трехфазного асинхронного двигателя. Чего-то не получается у меня его запустить. Кварц 4.0 МГц на ноги 5 и 6. От них же кондеры по 18 пФ на землю. +5 на 21, 1 и 3 ноги, общий - 22 и 4. На кварце нет генерации (на 5-ой ноге +5В, на 6-ой - 0В). Может где что упустил.

[Romanchik]

Спасибо за исходники!

Вопрос может глупый, но я с proteus познакомился час назад. :-)

1. Он сам компилирует из bas?
2. При запуске пишет:

SIMULATION LOG
==============
Design: D:\AC_PROTEUS\ac1.DSN
Doc. no.: <NONE>
Revision: <NONE>
Author: <NONE>
Created: 24/10/05
Modified: 14/03/06

Compiling source files...
Build completed OK.
Compiling netlist...
Linking netlist...
Partition analysis...

Simulating partition 1 [265019CB]...
Animation started sucessfully...
PROSPICE Release 6.7 SP0 © Labcenter Electronics 1993-2005.
SPICE Kernel Version 3f5. © Berkeley University ERL.

Reading netlist...
Reading SPICE models...
Loading library 'ANALOGD.SML'
Loading library 'APEX.SML'
Loading library 'BURRBROWN.SML'
Loading library 'ELANTEC.SML'
Loading library 'FAIRCHLD.SML'
Loading library 'INTERSIL.SML'
Loading library 'LINTEC.SML'
Loading library 'NATOA.SML'
Loading library 'SUPERTEX.SML'
Loading library 'TECCOR.SML'
Loading library 'TEX101.SML'
Loading library 'TEX301.SML'
Loading library 'TEX3_1.SML'
Loading library 'TEX401.SML'
Loading library 'TEX5_1.SML'
Loading library 'VALVES.SML'
Loading library 'ZETEX.SML'
Building circuit...
Instantiating SPICE models...
[U1] PIC18 model release 6.7 SP1 simulating 'PIC18F252' device.
[U1] [BASIC] ERROR: Unable to parse target information from list file.
Loader Terminated.
[U1] [BASIC] ERROR: No File List block was found within the list file. Please ensure that the basic file has been
compiled with Version 1.24 or later of the Crownhill PIC Basic Plus Compiler
and that all associated files are in the same directory as the .BAS file.
[U1] [BASIC] ERROR: No Variable List block was found within the list file. Please ensure that the basic file has been
compiled with Version 1.24 or later of the Crownhill PIC Basic Plus Compiler
and that all associated files are in the same directory as the .BAS file.
[U1] [BASIC] ERROR: Unable to open file '..\ACMOTOR\AC_MOT~1.HEX' - the file could not be located in the same directory as the .BAS project file.

ERROR: [U1] Failed to load BASIC file '..\ACMOTOR\AC_MOTOR1.bas'
[U1] Loaded 0 program bytes and 0 data bytes.
[U1] Loaded 256 bytes of persistent EEPROM data.
[U1] Execution (instruction) clock frequency is 20.0MHz
[DSIM] BOOT Error.
Real Time Simulation failed to start
Warning: [U1] at 0.00 (PC=0x0000): No instruction cycles were executed - processor may never have made it out of reset!

Real Time Simulation FAILED.


Что поправить нужно?

[Kabron]

Hi, Romanchik
Ну че разобрался, помогло?