Правка файла борды, при каких условиях Опции

[Tarbal]

Однажды у меня выла такая проблема при монтировании файловой системы с СДкарты.
Монтировалась как RW, а на СДкарте стояла защита от записи.


1. Подключите терминал к сериальному выходу (полагаю уже подключен раз вы видите сообщения)
2. Включите питание и в момент счета счетчика u-boot нажмите пробел (иногда enter).
3. если все остановилось наберите printenv
4. Все что напечаталось скопируйте и покажите нам.

На каком диске ваша рут файловая система?

Спасибо, познавательно. Честно говоря я так и знал что нигде кроме как в mach-type.h и при вызове MACHINE_START этот id не упоминается.
У меня ситуация такая: u-boot собран для одной машины (с конкретным id), а ядро новое не содержало такого machine id. Я просто взял и поменял руками номер для борды в файле mach-types.h
не помогло.

1 )Вопрос:

имеем MACHINE_START(MX53_LOCO, "Freescale MX53 LOCO Board"). Проверяется ли где то второй аргумент? или это только для вывода на экран?

2) в новых версиях ядер файл борды разделён на две части (board_xxx.c и board_xxx.dts). Вижу что не для всех aайлов board_xxx.c, которые в ядре по умолчанию, есть соответствующий board_xxx.dts что странно...

Я хорошо знаком с LOCO бордом. И этот файл хорошо перелопатил. MACHINE_START(MX53_LOCO, "Freescale MX53 LOCO Board") берет из сгенерированного файла хедера константу .....MX53_LOCO. вместо точек у них у всех одно и то же. сами найдете в хедере. Я не понмю. Вот эта константа и должна соответствовать бут лоадеру.
Я поменял текст "Freescale MX53 LOCO Board", но начались проблемы. Пока я разбирался, то обнаручил, что если оставить "Freescale MX53" в начале и дописать далее свой текст, то все работает безупречно.

В ядре 2.6 каждому устройству создавалась структура. В функции
static void __init mx53_loco_board_init(void)

часть из них регистрируется. Как сделано для остальных устройств я не помню. Был еще один файл в котором все устройства оформлены в виде структур, но давно с этим не возился.

В более поздних версиях кернела вместо разрозненных структур используется единое дерево устройств, где все собрано вместе и легко конфигурировать параметры.

Сообщение отредактировал Tarbal - Apr 4 2014, 21:02

[TigerSHARC]

Полный лог загрузки ядра

CODE

NAND read: device 0 offset 0x80000, size 0x280000
2621440 bytes read: OK
## Booting kernel from Legacy Image at c0700000 ...
Image Name: Linux-3.3.0
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2235936 Bytes = 2.1 MB
Load Address: c0008000
Entry Point: c0008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
':dt-0004096' (c7002b4c): fill_kobj_path: path = '/kernel/slab/:dt-0004096'
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
msgmni has been set to 228
io scheduler noop registered (default)
da8xx_lcdc da8xx_lcdc.0: GLCD: No valid panel found
Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x1c42000 (irq = 25) is a AR7
serial8250.0: ttyS1 at MMIO 0x1d0c000 (irq = 53) is a AR7
serial8250.0: ttyS2 at MMIO 0x1d0d000 (irq = 61) is a AR7
console [ttyS2] enabled
ahci ahci: forcing PORTS_IMPL to 0x1
ahci ahci: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
ahci ahci: flags: ncq sntf pm led clo only pmp pio slum part ccc
scsi0 : ahci_platform
ata1: SATA max UDMA/133 mmio [mem 0x01e18000-0x01e19fff] port 0x100 irq 67
UBI error: ubi_init: UBI error: cannot initialize UBI, error -2
davinci_mdio davinci_mdio.0: davinci mdio revision 1.5
davinci_mdio davinci_mdio.0: detected phy mask fffffffd
davinci_mdio.0: probed
davinci_mdio davinci_mdio.0: phy[1]: device davinci_mdio-0:01, driver SMSC LAN8710/LAN8720
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci ohci.0: DA8xx OHCI
ohci ohci.0: new USB bus registered, assigned bus number 1
Waiting for USB PHY clock good...
ohci ohci.0: irq 59, io mem 0x01e25000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
input: TPS6507x Touchscreen as /devices/platform/i2c-gpio.1/i2c-1/1-0048/input/input0
omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0
omap_rtc: RTC power up reset detected
i2c /dev entries driver
watchdog watchdog: heartbeat 60 sec
cpuidle: using governor ladder
cpuidle: using governor menu
davinci_mmc davinci_mmc.1: Using DMA, 4-bit mode
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP cubic registered
NET: Registered protocol family 17
regulator_init_complete: LDO2: incomplete constraints, leaving on
regulator_init_complete: LDO1: incomplete constraints, leaving on
regulator_init_complete: VDCDC3: incomplete constraints, leaving on
regulator_init_complete: VDCDC2: incomplete constraints, leaving on
regulator_init_complete: VDCDC1: incomplete constraints, leaving on
davinci_emac davinci_emac.1: using random MAC addr: ce:65:6a:e9:01:62
omap_rtc omap_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
ata1: SATA link down (SStatus 0 SControl 300)
VFS: Cannot open root device "ubi0:rootfs" or unknown-block(0,0)
Please append a correct "root=" boot option; here are the available partitions:
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)

вывод printenv в U-boot:

CODE

baudrate=115200
ethaddr=00:11:22:33:44:55
bootdelay=2
ipaddr=192.168.0.107
serverip=192.168.0.103
mtdids=nand0=davinci_nand.0
mtdparts=mtdparts=davinci_nand.0:128k(uboot_env),384k(uboot),2560k(kernel),-(ubi)
partition=nand0,0
mtddevnum=0
mtddevname=uboot_env
bootargs=ip=192.168.0.107:192.168.0.103:192.168.0.1:255.255.255.0:Owlboard:eth0 rootfstype=ubifs root=ubi0:rootfs ubi.mtd=ubi rw mem=128M
autoboot=nand read.e 0xc0700000 kernel; bootm 0xc0700000
bootcmd=run autoboot
stdin=serial
stdout=serial
stderr=serial
ver=U-Boot 2009.11 (Nov 24 2012 - 16:05:51)

Самое странное, у меня полность совпадают переменные окружения u-boot и строки bootargs в ядре у старого и нового ядра.
Старое грузится нормально, новое нет((

[aaarrr]

Если работает сеть, загрузитесь с nfs. Потом можно будет спокойно разобраться с NAND и ubi.

[TigerSHARC]

Если работает сеть, загрузитесь с nfs. Потом можно будет спокойно разобраться с NAND и ubi.

если загружусь с nfs, как мне понять, что нужно делать чтобы разобраться с NAND?

[Jury093]

рутовая на NAND, поддержка ubifs включена в ядре

а вас вот тут ошибка:

Код

UBI error: ubi_init: UBI error: cannot initialize UBI, error -2

ubifs включается в двух местах - сделано?
полный лог можно копипастить на pastebin.com и линк сюда..

в логе должно быть примерно такое (с вашими реалиями):

Код

[    0.968719] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08ABAEAWP)
[    0.977294] Creating 8 MTD partitions on "omap2-nand.0":
[    0.982879] 0x000000000000-0x000000020000 : "SPL"
[    0.989166] 0x000000020000-0x000000040000 : "SPL.backup1"
[    0.996124] 0x000000040000-0x000000060000 : "SPL.backup2"
[    1.003051] 0x000000060000-0x000000080000 : "SPL.backup3"
[    1.009948] 0x000000080000-0x000000260000 : "U-Boot"
[    1.017211] 0x000000260000-0x000000280000 : "U-Boot Env"
[    1.024108] 0x000000280000-0x000000780000 : "Kernel"
[    1.032653] 0x000000780000-0x000010000000 : "File System"

и при монтирование размеченного раздела:

CODE

[ 133.922149] UBI: attaching mtd7 to ubi0
[ 133.926269] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 133.932800] UBI: logical eraseblock size: 126976 bytes
[ 133.938446] UBI: smallest flash I/O unit: 2048
[ 133.943359] UBI: VID header offset: 2048 (aligned 2048)
[ 133.949615] UBI: data offset: 4096
[ 136.081298] UBI: max. sequence number: 10
[ 136.105377] UBI: attached mtd7 to ubi0
[ 136.109313] UBI: MTD device name: "File System"
[ 136.115081] UBI: MTD device size: 248 MiB
[ 136.120269] UBI: number of good PEBs: 1988
[ 136.125183] UBI: number of bad PEBs: 0
[ 136.129821] UBI: number of corrupted PEBs: 0
[ 136.134460] UBI: max. allowed volumes: 128
[ 136.139282] UBI: wear-leveling threshold: 4096
[ 136.144195] UBI: number of internal volumes: 1
[ 136.148834] UBI: number of user volumes: 1
[ 136.153472] UBI: available PEBs: 0
[ 136.158111] UBI: total number of reserved PEBs: 1988
[ 136.163299] UBI: number of PEBs reserved for bad PEB handling: 19
[ 136.169647] UBI: max/mean erase counter: 5/2
[ 136.174102] UBI: image sequence number: 0
[ 136.178405] UBI: background thread "ubi_bgt0d" started, PID 1166
[ 139.822357] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[ 139.828704] UBIFS: file system size: 247984128 bytes (242172 KiB, 236 MiB, 1953 LEBs)
[ 139.837066] UBIFS: journal size: 12443648 bytes (12152 KiB, 11 MiB, 98 LEBs)
[ 139.844970] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 139.851257] UBIFS: default compressor: lzo
[ 139.855560] UBIFS: reserved for root: 4952683 bytes (4836 KiB)

успешное наличие из первой части лога можно посмотреть:

Код

root@неважно:~# ls /dev/mtd*
/dev/mtd0    /dev/mtd1ro  /dev/mtd3    /dev/mtd4ro  /dev/mtd6    /dev/mtd7ro     /dev/mtdblock2  /dev/mtdblock5
/dev/mtd0ro  /dev/mtd2    /dev/mtd3ro  /dev/mtd5    /dev/mtd6ro  /dev/mtdblock0  /dev/mtdblock3  /dev/mtdblock6
/dev/mtd1    /dev/mtd2ro  /dev/mtd4    /dev/mtd5ro  /dev/mtd7    /dev/mtdblock1  /dev/mtdblock4  /dev/mtdblock7

второй:

Код

root@неважно:~# ls /dev/ubi*
/dev/ubi0  /dev/ubi0_0  /dev/ubi_ctrl

Сообщение отредактировал Jury093 - Apr 5 2014, 15:36

[Tarbal]

А в случае когда грузится, что пишет про монтирование файловой системы? Можете скопировать?

Сравните в конфигурации ядер есть ли разница в определении всего имеющего отношение к драйверам флэш памяти.

[TigerSHARC]

прошу прощения, проблема по прежнему не решена.
Вот полный лог загрузки, рабочей системы:

CODE

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[ 0.000000] Linux version 2.6.37 (rusar@v1310) (gcc version 4.4.1 (Sourcery G++ Lite 2009q3-67) ) #116 PREEMPT Wed Nov 28 18:20:03 EET 2012
[ 0.000000] CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Owlboard Plus OMAP-L138/AM1808
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] DaVinci da850/omap-l138/am18x variant 0x1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: ip=192.168.0.107:192.168.0.103:192.168.0.1:255.255.255.0:Owlboard:eth0 rootfstype=ubifs root=ubi0:rootfs ubi.mtd=ubi rw mem=128M
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 128MB = 128MB total
[ 0.000000] Memory: 124988k/124988k available, 6084k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xff000000 - 0xffe00000 ( 14 MB)
[ 0.000000] vmalloc : 0xc8800000 - 0xfea00000 ( 866 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .init : 0xc0008000 - 0xc0031000 ( 164 kB)
[ 0.000000] .text : 0xc0031000 - 0xc0486000 (4436 kB)
[ 0.000000] .data : 0xc0486000 - 0xc04b4820 ( 187 kB)
[ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Preemptable hierarchical RCU implementation.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:245
[ 0.000000] Console: colour dummy device 80x30
[ 0.000372] Calibrating delay loop... 185.54 BogoMIPS (lpj=927744)
[ 0.220077] pid_max: default: 32768 minimum: 301
[ 0.220492] Mount-cache hash table entries: 512
[ 0.221599] CPU: Testing write buffer coherency: ok
[ 0.223995] devtmpfs: initialized
[ 0.232429] DaVinci: 144 gpio irqs
[ 0.232972] regulator: core version 0.5
[ 0.235499] regulator: dummy:
[ 0.236154] NET: Registered protocol family 16
[ 0.287562] mcbsp1 0
[ 0.452957] bio: create slab <bio-0> at 0
[ 0.461922] SCSI subsystem initialized
[ 0.469973] usbcore: registered new interface driver usbfs
[ 0.471353] usbcore: registered new interface driver hub
[ 0.472644] usbcore: registered new device driver usb
[ 0.485166] regulator: VDCDC1: 3200 <--> 3300 mV at 3300 mV
[ 0.488221] regulator: VDCDC2: 1750 <--> 3300 mV at 3300 mV
[ 0.491612] regulator: VDCDC3: 950 <--> 1350 mV at 1200 mV
[ 0.493968] regulator: LDO1: 1800 mV
[ 0.497024] regulator: LDO2: 1150 <--> 1300 mV at 1200 mV
[ 0.498383] i2c i2c-1: Invalid 7-bit I2C address 0x00
[ 0.498438] i2c i2c-1: Can't create device at 0x00
[ 0.498485] i2c i2c-1: Invalid 7-bit I2C address 0xa2
[ 0.498523] i2c i2c-1: Can't create device at 0xa2
[ 0.498588] i2c-gpio i2c-gpio.1: using pins 20 (SDA) and 21 (SCL)
[ 0.499674] vpif vpif: vpif probe success
[ 0.506674] Advanced Linux Sound Architecture Driver Version 1.0.23.
[ 0.509520] Switching to clocksource timer0_1
[ 0.608398] musb-hdrc: version 6.0, host, debug=0
[ 0.608721] musb-hdrc musb-hdrc: dma type: dma-cppi41
[ 0.610259] Waiting for USB PHY clock good...
[ 0.630576] musb-hdrc musb-hdrc: MUSB HDRC host driver
[ 0.630713] musb-hdrc musb-hdrc: new USB bus registered, assigned bus number 1
[ 0.634281] hub 1-0:1.0: USB hub found
[ 0.634420] hub 1-0:1.0: 1 port detected
[ 0.635354] musb-hdrc musb-hdrc: USB Host mode controller at fee00000 using DMA, IRQ 58
[ 0.637114] NET: Registered protocol family 2
[ 0.637539] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.638595] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.638859] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.639046] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.639084] TCP reno registered
[ 0.639129] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.639199] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.640155] NET: Registered protocol family 1
[ 0.641722] RPC: Registered udp transport module.
[ 0.641779] RPC: Registered tcp transport module.
[ 0.641815] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.644620] EMAC: RMII PHY configured, MII PHY will not be functional
[ 0.759170] NTFS driver 2.1.29 [Flags: R/O].
[ 0.763385] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.768516] msgmni has been set to 244
[ 0.775492] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.775562] io scheduler noop registered
[ 0.775600] io scheduler deadline registered
[ 0.776190] io scheduler cfq registered (default)
[ 0.778598] da8xx_lcdc da8xx_lcdc.0: GLCD: Found DT_atm0700d4 panel
[ 0.806108] Console: switching to colour frame buffer device 100x30
[ 0.848461] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[ 0.856046] serial8250.0: ttyS0 at MMIO 0x1c42000 (irq = 25) is a AR7
[ 0.859126] serial8250.0: ttyS1 at MMIO 0x1d0c000 (irq = 53) is a AR7
[ 0.862662] serial8250.0: ttyS2 at MMIO 0x1d0d000 (irq = 61) is a AR7
[ 1.362661] console [ttyS2] enabled
[ 1.373204] ahci ahci: forcing PORTS_IMPL to 0x1
[ 1.378106] ahci ahci: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[ 1.386385] ahci ahci: flags: ncq sntf pm led clo only pmp pio slum part ccc
[ 1.398567] scsi0 : ahci_platform
[ 1.405152] ata1: SATA max UDMA/133 mmio [mem 0x01e18000-0x01e19fff] port 0x100 irq 67
[ 1.421365] NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung )
[ 1.430507] Creating 4 MTD partitions on "davinci_nand.1":
[ 1.436140] 0x000000000000-0x000000020000 : "uboot_env"
[ 1.444660] 0x000000020000-0x000000080000 : "uboot"
[ 1.452622] 0x000000080000-0x000000300000 : "kernel"
[ 1.460803] 0x000000300000-0x000008000000 : "ubi"
[ 1.468732] davinci_nand davinci_nand.1: controller rev. 2.5
[ 1.478268] UBI: attaching mtd3 to ubi0
[ 1.482600] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 1.488940] UBI: logical eraseblock size: 129024 bytes
[ 1.494616] UBI: smallest flash I/O unit: 2048
[ 1.499402] UBI: sub-page size: 512
[ 1.504422] UBI: VID header offset: 512 (aligned 512)
[ 1.510462] UBI: data offset: 2048
[ 1.559998] usb 1-1: new high speed USB device using musb-hdrc and address 2
[ 1.759966] ata1: SATA link down (SStatus 0 SControl 300)
[ 1.868011] UBI: max. sequence number: 244
[ 1.893233] UBI: attached mtd3 to ubi0
[ 1.897074] UBI: MTD device name: "ubi"
[ 1.902117] UBI: MTD device size: 125 MiB
[ 1.907144] UBI: number of good PEBs: 996
[ 1.912013] UBI: number of bad PEBs: 4
[ 1.916513] UBI: number of corrupted PEBs: 0
[ 1.921117] UBI: max. allowed volumes: 128
[ 1.925787] UBI: wear-leveling threshold: 4096
[ 1.930662] UBI: number of internal volumes: 1
[ 1.935155] UBI: number of user volumes: 2
[ 1.939738] UBI: available PEBs: 0
[ 1.944249] UBI: total number of reserved PEBs: 996
[ 1.949169] UBI: number of PEBs reserved for bad PEB handling: 9
[ 1.955317] UBI: max/mean erase counter: 3/1
[ 1.959920] UBI: image sequence number: -1958061123
[ 1.964997] UBI: background thread "ubi_bgt0d" started, PID 513
[ 1.971658] spi_davinci spi_davinci.1: DMA: supported
[ 1.976830] spi_davinci spi_davinci.1: DMA: RX channel: 18, TX channel: 19, event queue: 0
[ 1.988168] m25p80 spi1.0: mx25l6405d (8192 Kbytes)
[ 1.993450] Creating 4 MTD partitions on "mx25l6405d":
[ 1.998678] 0x000000000000-0x000000080000 : "U-Boot"
[ 2.006545] 0x000000080000-0x0000000c0000 : "U-Boot-Env"
[ 2.015022] 0x0000000c0000-0x000000340000 : "Kernel"
[ 2.023146] 0x000000340000-0x000000800000 : "Filesystem"
[ 2.031604] spi_davinci spi_davinci.1: Controller at 0xfef0e000
[ 2.089754] davinci_mdio davinci_mdio.0: davinci mdio revision 1.5
[ 2.096040] davinci_mdio davinci_mdio.0: detected phy mask fffffffd
[ 2.104559] davinci_mdio.0: probed
[ 2.108047] davinci_mdio davinci_mdio.0: phy[1]: device 0:01, driver SMSC LAN8710/LAN8720
[ 2.117486] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.124448] ohci ohci.0: DA8xx OHCI
[ 2.128118] ohci ohci.0: new USB bus registered, assigned bus number 2
[ 2.134991] Waiting for USB PHY clock good...
[ 2.139577] ohci ohci.0: irq 59, io mem 0x01e25000
[ 2.207451] hub 2-0:1.0: USB hub found
[ 2.211689] hub 2-0:1.0: 1 port detected
[ 2.217287] Initializing USB Mass Storage driver...
[ 2.223950] scsi1 : usb-storage 1-1:1.0
[ 2.231800] usbcore: registered new interface driver usb-storage
[ 2.237917] USB Mass Storage support registered.
[ 2.245612] mice: PS/2 mouse device common for all mice
[ 2.255203] input: TPS6507x Touchscreen as /devices/platform/i2c-gpio.1/i2c-1/1-0048/input/input0
[ 2.271133] omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0
[ 2.277574] omap_rtc: RTC power up reset detected
[ 2.282863] omap_rtc: already running
[ 2.288388] i2c /dev entries driver
[ 2.300674] Linux video capture interface: v2.00
[ 2.311650] cpia2: V4L-Driver for Vision CPiA2 based cameras v3.0.0
[ 2.319195] usbcore: registered new interface driver cpia2
[ 2.329877] gspca: v2.10.0 registered
[ 2.346019] tvp514x: tvp514x decoder driver registered !!
[ 2.356973] vpif_capture vpif_capture: registered sub device tvp514x-0
[ 2.364031] vpif_capture vpif_capture: VPIF Capture driver initialized
[ 2.378237] usbcore: registered new interface driver uvcvideo
[ 2.389368] USB Video Class driver (v1.0.0)
[ 2.394126] watchdog watchdog: heartbeat 60 sec
[ 2.403677] cpuidle: using governor ladder
[ 2.416549] cpuidle: using governor menu
[ 2.422714] sdhci: Secure Digital Host Controller Interface driver
[ 2.428974] sdhci: Copyright© Pierre Ossman
[ 2.434046] davinci_mmc: probe of davinci_mmc.0 failed with error -16
[ 2.447759] davinci_mmc davinci_mmc.1: Using DMA, 4-bit mode
[ 2.463078] usbcore: registered new interface driver usbhid
[ 2.468756] usbhid: USB HID core driver
[ 2.506309] asoc: tlv320aic3x-hifi <-> davinci-mcbsp.1 mapping ok
[ 2.521796] ALSA device list:
[ 2.524833] #0: DA850/OMAP-L138 EVM
[ 2.536099] TCP cubic registered
[ 2.539407] NET: Registered protocol family 17
[ 2.555321] regulator_init_complete: incomplete constraints, leaving LDO2 on
[ 2.572196] regulator_init_complete: incomplete constraints, leaving LDO1 on
[ 2.580429] regulator_init_complete: incomplete constraints, leaving VDCDC3 on
[ 2.588562] regulator_init_complete: incomplete constraints, leaving VDCDC2 on
[ 2.601087] regulator_init_complete: incomplete constraints, leaving VDCDC1 on
[ 2.609071] davinci_emac_probe: using random MAC addr: d6:c7:e1:28:81:76
[ 2.636240] omap_rtc omap_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
[ 3.152426] davinci_mdio davinci_mdio.0: resetting idled controller
[ 3.160549] net eth0: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=0:01, id=7c0f1)
[ 3.232071] scsi 1:0:0:0: Direct-Access USB 2.0 USB Flash Drive 0.00 PQ: 0 ANSI: 2
[ 3.253954] sd 1:0:0:0: [sda] 7897088 512-byte logical blocks: (4.04 GB/3.76 GiB)
[ 3.262337] sd 1:0:0:0: Attached scsi generic sg0 type 0
[ 3.276788] sd 1:0:0:0: [sda] Write Protect is off
[ 3.287363] sd 1:0:0:0: [sda] Assuming drive cache: write through
[ 3.307041] sd 1:0:0:0: [sda] Assuming drive cache: write through
[ 3.377598] sda: sda1
[ 3.452103] sd 1:0:0:0: [sda] Assuming drive cache: write through
[ 3.458295] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 4.180514] IP-Config: Complete:
[ 4.183657] device=eth0, addr=192.168.0.107, mask=255.255.255.0, gw=192.168.0.1,
[ 4.196653] host=Owlboard, domain=, nis-domain=(none),
[ 4.202439] bootserver=192.168.0.103, rootserver=192.168.0.103, rootpath=
[ 4.266018] UBIFS: recovery needed
[ 4.328200] UBIFS: recovery completed
[ 4.332103] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[ 4.338211] UBIFS: file system size: 49287168 bytes (48132 KiB, 47 MiB, 382 LEBs)
[ 4.349752] UBIFS: journal size: 2451456 bytes (2394 KiB, 2 MiB, 19 LEBs)
[ 4.357166] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 4.379738] UBIFS: default compressor: lzo
[ 4.383926] UBIFS: reserved for root: 2327954 bytes (2273 KiB)
[ 4.392289] VFS: Mounted root (ubifs filesystem) on device 0:14.
[ 4.404871] devtmpfs: mounted
[ 4.408093] Freeing init memory: 164K
[ 4.930983] UBIFS: recovery needed
[ 4.968886] UBIFS: recovery completed
[ 4.977762] UBIFS: mounted UBI device 0, volume 1, name "storage"
[ 4.984098] UBIFS: file system size: 75220992 bytes (73458 KiB, 71 MiB, 583 LEBs)
[ 4.991951] UBIFS: journal size: 3741696 bytes (3654 KiB, 3 MiB, 29 LEBs)
[ 4.999356] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 5.009735] UBIFS: default compressor: lzo
[ 5.013918] UBIFS: reserved for root: 3552872 bytes (3469 KiB)
Starting logging: OK
Initializing random number generator... done.
Starting network...
ip: RTNETLINK answers: File exists
Starting dropbear sshd: OK
Starting sshd: Could not load host key: /etc/ssh_host_dsa_key

Could not load host key: /etc/ssh_host_ecdsa_key

OK
Starting HPA's tftpd: /etc/init.d/S80tftpd-hpa: line 79: /usr/sbin/in.tftpd: not found
thttpd
root /root # 

сравнивал логи рабочей и не рабочей системы, зметил что в рабочей версии удивительным оразом всё последовательно настраивается, монтируются разделы UBI файловой системы. В нерабочем враинте всё совсем не так. Хотя конфиги практически идентичны и фалы борды одинаковые. Различаются версии ядер.

[Jury093]

прошу прощения, проблема по прежнему не решена.
Вот полный лог загрузки, рабочей системы:

более интересен лог нерабочей системы, фильтрация из .config (grep UBI, grep MTD, grep NAND) и куски файла борды, касающиеся нанда..

совсем не так. Хотя конфиги практически идентичны и фалы борды одинаковые. Различаются версии ядер.

пробейте по гуглю - может именно в этой версии ядра глючная подсистема (nand, ubifs)