DMA_InitTypeDef  DMA_InitStruct;
  
  DMA_ChannelCmd(DMA_Channel0, DISABLE);                      // Disable the DMA channel
  DMA_ChannelCmd(DMA_Channel1, DISABLE);                      // Disable the DMA channel
  
  /* RECIVE */
  DMA_StructInit(&DMA_InitStruct);

  /* Write the first LLI*/
  DMA_InitStruct.DMA_Channel_LLstItm = 0;                     // Set the addresses of next linked list for the first LLI structure
  DMA_InitStruct.DMA_Channel_SrcAdd = (u32)&(SSP0->DR);       // source address for the first LLI structure
  DMA_InitStruct.DMA_Channel_DesAdd = (u32)pData;             // Destination address for the first LLI structure
  DMA_InitStruct.DMA_Channel_SrcWidth = DMA_SrcWidth_Byte;    // The source bus width is a byte
  DMA_InitStruct.DMA_Channel_DesWidth = DMA_SrcWidth_Byte;    // The Destination bus width is a byte
  DMA_InitStruct.DMA_Channel_FlowCntrl = DMA_FlowCntrl_Perip2;// DMA is The flow controller
  DMA_InitStruct.DMA_Channel_TrsfSize = 512;                  // Transfer size
  DMA_InitStruct.DMA_Channel_Src = DMA_SRC_SSP0_RX;           // Chanel source

  /* Configure the DMA channel1 "the chosen channel to perform the transfer" */

  DMA_ChannelSRCIncConfig (DMA_Channel0, DISABLE);
  DMA_ChannelDESIncConfig (DMA_Channel0, ENABLE);
  DMA_SyncConfig(0, ENABLE);

  DMA_Init(DMA_Channel0,&DMA_InitStruct);                     // update the DMA channel1 registers with the cfirst LLI structure
  
  /* TRANSFER */
  DMA_StructInit(&DMA_InitStruct);

  /* Write the first LLI*/
  DMA_InitStruct.DMA_Channel_LLstItm = 0;                     // Set the addresses of next linked list for the first LLI structure
  DMA_InitStruct.DMA_Channel_SrcAdd = (u32)pData;             // source address for the first LLI structure
  DMA_InitStruct.DMA_Channel_DesAdd = (u32)&(SSP0->DR);       // Destination address for the first LLI structure
  DMA_InitStruct.DMA_Channel_SrcWidth = DMA_SrcWidth_Byte;    // The source bus width is a byte
  DMA_InitStruct.DMA_Channel_DesWidth = DMA_SrcWidth_Byte;    // The Destination bus width is a byte
  DMA_InitStruct.DMA_Channel_FlowCntrl = DMA_FlowCntrl_Perip1;// DMA is The flow controller
  DMA_InitStruct.DMA_Channel_TrsfSize = 512;                  // Transfer size
  DMA_InitStruct.DMA_Channel_Src = DMA_DES_SSP0_TX;           // Chanel destination

  /* Configure the DMA channel1 "the chosen channel to perform the transfer" */

  DMA_ChannelSRCIncConfig(DMA_Channel1, ENABLE);
  DMA_ChannelDESIncConfig(DMA_Channel1, DISABLE);
  DMA_SyncConfig(1, ENABLE);

  DMA_Init(DMA_Channel1,&DMA_InitStruct);                     // update the DMA channel1 registers with the cfirst LLI structure
  
  DMA_ChannelCmd(DMA_Channel0,ENABLE);                        // Enable the DMA channel
  DMA_ChannelCmd(DMA_Channel1,ENABLE);                        // Enable the DMA channel
  
  

  /*wait for the fifo to be empty*/
  while(DMA_GetChannelActiveStatus(DMA_Channel1));